Fallout Prop Nuka Cola Qtm. V4 Single

I have recreated my Nuka Cola Quantum Formula yet again, leading to the version four variant. Version three eventually had separation issues, leading it to be a medium blue. This new variant gives the Quantum a bluish ultraviolet color, which looks a lot closer to what it should look like.

This new variant still uses drink mix packets, however, it doesn't use the Hawaian Punch drink mix packets anymore. It now uses Crystal Light Energy Grape packets. Partial credit goes to for the creation of the labels.

---Nuka Cola Quantum Version 4---

---What you will need---
-1 Mexican Coca-Cola 355ml (12 fl oz.)
-1 to 5 American Coca-Cola 8 fl oz. (For extra bottle caps to reseal the Mexican bottle)
-1 Bottle Cap Opener
-Blue Food Coloring
-2 Packets of Crystal Light Energy Grape Water Flavoring
-1 Hammer
-1 bottle of Tonic Water (12 oz. or more)
-1 Instant Krazy Glue Pen
-1 Pair of Scissors
-1 Measuring cup of at least 500 ml.
-1 Funnel
-1 Roll/Plastic Dispenser of Invisible Tape
-Nuka Cola Cap Printouts from [link]
-Nuka Cola Quantum Label (Each label can be printed out in MS Paint, dimensions per label after copying and pasting if done properly from sheet: 367 X 140 Pixels.) Printout from Printout from [link]
-1 Utility Plyers with Serrated Saw Attachment (one that won't cut you, I used a Gerber Suspension)
-1 Soap Pad

---Instructions---

-1. Printout the required items mentioned above. If you already printed out a Nuka Cola Cap printout for another Nuka Cola drink project, naturally, don't prin't another cap sheet.

-2. Use the serrated saw attachment from the utility plyers to carefully scrape off the painted label off the Mexican Coca-Cola bottle(Doing so in a rough manner can scrape or even crack the bottle). This can take anywhere from fourty minutes to two hours. This is not manditory, however, strongly recommended, as the paper printout label becomes a bit translucent when the bottle is held upto the light after the label is applied, and if the Coca-Cola label is not peeled off, it becomes noticable.

-3. Use a Soap Pad around the area where the painted label was. This will loosen up and remove any really small specs of painted label that the Untility Plyers may have missed. Dry the bottle afterwards.

-4. Pry off the lid to the Mexican Coca-Cola with a bottle cap opener and enjoy it. You deserve it .

-5. Carefully clean out the bottle with Soap and hot water after enjoying your drink(This ensures that no Coca-Cola will mix with the mixture, creating an awkward color). Let the bottle dry.

-6. While letting the bottle dry, carefully remove the cap(s) off the American Coca-Cola(s) with a bottlecap opener as you will need them to reseal the Mexican bottle later (The Mexican Coca-Cola Bottlecaps are lower grade aluminum, and very rarely reseal. If you can repeatedly successfully use Mexican Coca-Cola Bottlecaps, kudos to you). It can take several caps to get it right. Enjoy your drink and share some with your friends .

-7. Open the bottle of Tonic Water and pour it into the measuring cup until you have 355 ml or 12 oz., and then using the funnel, pour it into the empty Mexican Coca-Cola bottle. Now add three drops of blue food coloring to the Tonic Water. Then add in the two packets of the Crystal light Energy Grape flavoring mix.

-8. Try to seal the bottle using the American Coca-Cola bottlecap(s). Shake lightly to see if you hear any carbonation escaping. If so, use the hammer and care fully hammer around bottlcap uptop (Hammering in the middle flattens the cap down, forcing the edges to popup). Once you no longer hear carbonation after shaking, turn the bottle upside down, and observe for leakage. if there is any, hammer as necessary or try another cap.If there is no leakage, repeat the leakage test two more times.

-9. Upon completion of the leakage test, assuming there is no leakage, shake the bottle lightly a bit to mix the Jones Soda and the blue food coloring.

-10. Cut out a cap printout, flip it upside down, and with the Krazy Glue Pen, apply some super glue to the upside-down printout.

-11. Apply the cut out cap with the superglue rightside up to the Mexican Coca-Cola Bottlecap and let dry.

-12. Cut out the labels and use the invisible tape to apply them to the bottle. There are several ways this can be done, so find out a way that works best for you.

-Note: This concoction is drinkable and tastes rather good. It also glows in front of a neon light as well as a black light. Unlike the game disclaimer, no, there is no Strontium Radioactive Isotope in this drink, no, it will not give you +20 Action Points, and no, drinking this will not make your urine glow for a week.